Italian corvette Cristoforo Colombo (1892)

Design

In the late 1880s, the Italian Regia Marinas chief designer, Benedetto Brin, prepared the design for a new screw corvette to replace the earlier , which was by then more than a decade old. The new vessel is sometimes referred to as a reconstruction of the original vessel, but they were in fact distinct ships. That vessel's wooden hull had been superseded by newer steel-hulled ships like and that had been completed in the early 1880s. Brin's new design was an essential copy of the earlier vessel, though with a steel hull instead of the wooden one used in the old corvette. The Regia Marina intended to use the new ship as a colonial station ship in the Red Sea to help control Italian Eritrea. The new Cristoforo Colombo proved to be the final corvette of the Italian fleet; the navy thereafter turned to protected cruisers like for its colonial patrol duties.

Characteristics

Cristoforo Colombo was 76.4 m long between perpendiculars, with a beam of 11.3 m and a draft of 5.69 m. She displaced 2713 LT at full load. Her steel hull was sheathed in copper to reduce biofouling, which was necessary for a ship intended to be stationed far from the level of maintenance facilities in home ports. Cristoforo Colombo had a crew of 238 officers and enlisted men.

The ship was powered with the same machinery used in the older Cristoforo Colombo, though it produced a lower speed. The engine was a 3-cylinder marine steam engine, which drove a single propeller shaft. Steam was provided by six boilers that were ducted into a pair of funnels. The propulsion system produced a top speed of 13 kn from 2321 ihp, though the contemporary source The Naval Pocket-Book credits the ship with a top speed of 15 kn from 3780 ihp. Coal storage capacity amounted to 445 LT. To supplement the steam engine, particularly on long voyages to and from Italy's colonial empire, Cristoforo Colombo carried a barque sailing rig.

Cristoforo Colombo carried a relatively heavy gun battery for her small size, including eight 120 mm 40-caliber guns. These were placed in single mounts in sponsons, four guns per broadside. Later in the ship's career, two of these guns were removed. For close-range defense against torpedo boats, she carried a secondary battery of two 75 mm 24-caliber guns.

Service history

The keel for Cristoforo Colombo was laid down on 1 September 1890, and her completed hull was launched on 24 September 1892. Fitting-out work was completed on 16 October 1894, after which the ship entered service with the Regia Marina. She had already been formally assigned to the 3rd Department, based in Venice, on 1 October 1893, though she did not actually join the unit until the following year. In 1895, the ship was assigned to the Training Squadron to serve as a training ship for naval cadets in company with the corvette Flavio Gioia. The ship was based in Venice at that time.

By 1901, Cristoforo Colombo was assigned to the Red Sea to patrol Italy's East African colony in Italian Somaliland, along with the gunboats and and the training vessel Volta. She remained there the following year in company with Volturno. In 1903, the unit was renamed the Red Sea and Benadir Division, and was reinforced with the torpedo cruiser and the aviso . The following year, the unit consisted of Cristoforo Colombo, Volturno, the torpedo cruiser , and the aviso . The Regia Marina discarded the ship on 10 March 1907. Her ultimate fate is unknown.

Notes

References

• {{cite journal
• {{cite book
• {{cite book |editor-last=Gardiner |editor-first=Robert | url-access = registration
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite journal |editor-last=Garbett |editor-first=H.
• {{cite book |editor-last=Marshall |editor-first=Chris
• {{cite book