Polyspheric
title: "Polyspheric" type: doc version: 1 created: 2026-02-28 author: "Wikipedia contributors" status: active scope: public tags: ["chrysler-engines", "v8-engines"] topic_path: "general/chrysler-engines" source: "https://en.wikipedia.org/wiki/Polyspheric" license: "CC BY-SA 4.0" wikipedia_page_id: 0 wikipedia_revision_id: 0
::data[format=table title="Infobox automobile engine"]
| Field | Value |
|---|---|
| name | Chrysler Polyspheric |
| manufacturer | Chrysler |
| aka | |
| production | - Mound Road Engine, Detroit, MI |
| predecessor | Chrysler flathead six |
| successor | Chrysler A engine |
| configuration | Naturally aspirated 90° V8 |
| displacement | {{ubl |
| bore | {{ubl |
| stroke | {{ubl |
| block | Cast iron |
| head | Cast iron |
| valvetrain | OHV 2 valves x cyl. |
| fuelsystem | Carburetor |
| fueltype | Gasoline |
| oilsystem | Wet sump |
| coolingsystem | Water-cooled |
| power | 310 hp |
| :: |
| name = Chrysler Polyspheric | image = | manufacturer = Chrysler | aka = | production = - Mound Road Engine, Detroit, MI | predecessor = Chrysler flathead six | successor = Chrysler A engine | configuration = Naturally aspirated 90° V8 | displacement = {{ubl | 241.3 cuin | 259.2 cuin | 268.3 cuin | 299.3 cuin | 313.7 cuin | 324.6 cuin | 331.1 cuin | 353.1 cuin | bore = {{ubl | 3+7/16 in | 3+9/16 in | 3+5/8 in | 3+11/16 in | 3+13/16 in | 3+15/16 in | stroke = {{ubl | 3+1/4 in | 3+5/8 in | 3.80 in | block = Cast iron | head = Cast iron | valvetrain = OHV 2 valves x cyl. | compression = | fuelsystem = Carburetor | fueltype = Gasoline | oilsystem = Wet sump | coolingsystem = Water-cooled | power = 310 hp | specpower = | torque = | length = | width = | height = | weight =
The Polyspheric engines were V8 engines produced by Chrysler from 1955 to 1958 as lower-cost alternatives to its Hemi engines. These engines were based on the Hemi engines, using the same blocks and crankshaft parts, but completely different cylinder heads, pushrods, exhaust manifolds and pistons.
They were called Polyspheric or Poly engines, because they featured polyspherical-shaped (meaning "more than one sphere") combustion chambers. These were formed by two shallow concave domes where the intake and exhaust valve seats were.
Because these engines needed a less sophisticated rocker setup than a true hemi, with only a single rocker shaft in each head, they were also cheaper to produce and lighter. In the Chrysler literature, the Poly engines were also called single rocker shaft (SRS), while the Hemi engines were called dual rocker shaft (DRS).
These engines replaced Chrysler's flathead inline-six in the division's lower-priced cars, and were themselves gradually replaced by the Chrysler A engine beginning in mid-1956.
Dodge and Plymouth
Dodge and Plymouth both offered Poly versions of Dodge's Hemi engine. The Dodge versions were marketed as Red Ram or Super Red Ram (internal code A388).
241
The 241 displaced 3954 cc and was Plymouth's Poly version of the Dodge's 241 Hemi for 1955. Bore and stroke were the same as for the Dodge engine, at 3+7/16 in by 3+1/4 in, respectively (3+7/16 x). Maximum power claimed was 157 hp.
{{anchor|259|260}} 260
The 260, also known as the 259, displaced 4247 cc and was introduced in the middle of 1955 by Plymouth. It was a bored-out 241, having a 3+9/16 in bore and keeping the 3+1/4 in stroke (3+9/16 x). This engine was also used on 1955 and 1956 Dodge trucks. Maximum power claimed was 167 hp with a two-barrel carburetor; a four-barrel version with 177 hp was added later.
270
The 270 displaced 4397 cc and was offered in both Plymouths (1956) and Dodges (1955–1956). Like its predecessors, it was a Poly version of Dodge's 270 Hemi. Bore and stroke were the same as the Hemi's at 3+5/8 in by 3+1/4 in, respectively (3+5/8 x). Outputs are 180 or depending on fitment.
315
The 315 displaced 5141 cc and was a Poly version of Dodge's high-deck 315 Hemi. Bore and stroke were the same at 3.625 in by 3.8 in, respectively. Only used on 1956 Dodges.
325
The 325 displaced 5320 cc and was a Poly version of Dodge's largest high-deck 325 Hemi. Bore and stroke were the same at 3+11/16 in by 3.8 in, respectively. Used on 1957 and 1958 Dodge.
Chrysler
The Spitfire engines were Poly variants of Chrysler's FirePower (Hemi) engine. Chrysler built three Spitfire engines: the 331 Poly, 354 Poly, and the all-new 301 Poly, which did not have a Hemi version. They were introduced for 1955 in the low-priced Chrysler Saratoga and Windsor models and used through 1958.
All Chrysler Spitfire engines were low deck; no Poly version of the raised deck 392 Hemi engine was produced.
301
The 301 displaced 4905 cc and was Chrysler's smallest Poly engine. The 301 has a 3.625 in bore and a 3.625 in stroke.
331
The 331 displaced 5425 cc and was a Poly version of Chrysler's 331 Hemi. Bore and stroke were the same at 3+13/16 in by 3+5/8 in, respectively (3+13/16 x).
354
The 354 displaced 5787 cc and was a Poly version of Chrysler's 354 Hemi. Bore and stroke were the same at 3+15/16 in by 3+5/8 in, respectively (3+15/16 x). The 1958 Chrysler Saratoga with four-barrel carberutor (58S) was the most powerful at 310 hp.
References
References
- "The 1956-1967 Plymouth Polyspherical Head Explained". Automotive History Preservation Society.
::callout[type=info title="Wikipedia Source"] This article was imported from Wikipedia and is available under the Creative Commons Attribution-ShareAlike 4.0 License. Content has been adapted to SurfDoc format. Original contributors can be found on the article history page. ::